 |
| datasheet |
|
40Pro
Universal ISP Programmer |  |
First member of the new USB 2.0 compatible generation of Windows based programmers.
The 40Pro is built to
meet the demands of development labs and field engineers for universal, but
portable programming.
40Pro is a small, fast and powerful programmer designed for a huge range
of programmable devices. Using
built-in in-circuit serial programming (ISP) connector the programmer is
able to program ISP capable chips
incircuit. 40Pro isn't only a programmer, but also a static RAMs tester.
Very fast programming due to high-speed FPGA driven hardware and USB 2.0
full high speed port.
The 40Pro interfaces with IBM compatible PC's through the USB 2.0/1.1 port.
This gives full compatibility with
the latest PC's, notebooks and portables. |
- 40 powerful TTL pindrivers provide H/L/pull_up/pull_down
and read capability for each pin of socket.
Advanced pindrivers incorporate high-quality high-speed circuitry to
deliver signals without overshoot or
ground bounce for all supported devices. Pin drivers operate down to
1.8V so you'll be ready to program
the full range of today's advanced low-voltage devices.
- The programmer performs device insertion tests and contact checks
before it programs each device. These
capabilities, supported by signature-byte check help prevent
chip damage due to operator error.
-
40Pro programmer performs programming verifications at the marginal
level of supply voltage, which
improves programming yield, and guarantees long data retention.
- Various socket converters are available to handle device in
PLCC, SOIC, SSOP, TSOP, TSSOP, TQFP, QFN (MLF)
and other packages.
|
- Programmer is driven by an easy-to-use control program
with pull-down menus, hot keys and on-line
help. Selecting of the device is performed by class, manufacturer or
simply by typing a fragment of vendor
name and/or part number.
- Standard device-related commands (read, blank check, program, verify,
erase) are enhanced by some test
functions (insertion test, signature-byte check), and some special
functions (autoincrement).
- All
known data formats are supported. Automatic file format detection
and conversion during loading of file.
- The rich-featured autoincrement function enables one to assign
individual
serial numbers to each programmed device - or simply increments
a serial
number. The function also enables one to read serial numbers
or any
programmed device identification signatures from a file.
- The software also provides extensive information about programmable
devices including detailed drawings of all available packages.
The software
also provides explanations of chip labelling (prefixes and suffixes)
for each of
the supported chips.
- The software provides full information for ISP implementation:
Description of
ISP connector pins for the currently selected chip, recommended
target
design around in-circuit programmed chip and other necessary
information.
- Keeping your programmer software up to date can be a costly
business with
some programmers. Dataman offers completely FREE software updates
whenever you need them. The latest software is always available
from our
website.
|
The 40Pro supports over 13,000 of the most popular
devices in use today - with future devices being added monthly.
Programmer,
in ZIF socket - EPROM: NMOS/CMOS, 27xxx and 27Cxxx
series, with 8/16 bit data width, full
support of LV series
- EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit
data
width, full support of LV series
- Flash
EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx
series, with 8/16 bit data width, full support of LV series
- Serial E(E)PROM: 24Cxxx, 24Fxxx, 25Cxxx, 45Dxxx, 59Cxxx, 25Fxxx,
25Pxxx,
85xxx, 93Cxxx, full support for LV series
- Configuration (EE)PROM: XCFxxx, 37LVxx, XC17xxxx, EPCxxx,
AT17xxx, LV
series including
- NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR
2xxx, ZMD
U63x series
- PLD: series: Atmel, AMD-Vantis, Cypress, ICT, Lattice, NS,
...
- Microcontrollers 51 series: 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx,
89LVxxx, LPC
series. From all manufacturers, e.g. Atmel, Atmel W&M, Intel,
Philips, SST,
Winbond
- Microcontrollers Atmel AVR: ATtiny, AT90Sxxx, ATmega series
- Microcontrollers Cypress: CY8Cxxxxx
- Microcontrollers ELAN: EM78Pxxx
- Microcontrollers EM Microelectronic: 4 and 8 bit series
- Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx,
PIC17Cxxx, PIC18xxx, dsPIC series, 8- 40 pins
- Microcontrollers Scenix (Ubicom): SXxxx series
Programmer, through ISP connector
- Serial E(E)PROM: IIC series
- Microcontrollers Atmel: AT89Sxxx, AT90Sxxxx, ATtiny, ATmega series
- Microcontrollers Cypress: CY8C2xxxx
- Microcontrollers Elan: EM78Pxxx
- Microcontrollers EM Microelectronic: 4 and 8 bit series
- Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx,
PIC17xxx,
PIC18xxx, dsPIC series
- Microcontrollers Philips: LPC series
|
| Programmer |
| |
two D/A converters for VCCP and VPP, controllable rise and fall
time |
| |
VCCP range 2V..7V/350mA |
| |
VPP range 2V..25V/200mA |
| |
USB 2.0/1.1 compatible interface |
| |
auto calibration |
| |
self test capability |
| ZIF socket, pindriver |
| |
40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices
up to 40-pins |
| |
pindriver: 40 TTL pindrivers, specialized GND/VCC/VPP pindriver |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins; level H selectable from 1.8V up to 5V |
| |
continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
10-pin male type with miss insertion lock |
| |
5 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable
from 1.8V up to 5V to handle all (low-voltage including) devices |
| |
programmed chip voltage (VCCP) with both source/sink capability
and
voltage sense |
| Package Includes |
| |
40Pro Universal ISP Production Programmer
Dimensions: 160x95x35 mm (6.3x3.7x1.4 inches)
Weight: 500g (17.65 oz) |
| |
Wall plug adapter, 15V/500mA, unstabilized |
| |
Moulded USB Cable |
| |
ISP cable |
| |
Diagnostic POD for self test of the programmer |
| |
Anti-dust cover for ZIF socket |
| |
User manual |
| |
Software |
| |
Transport case |
| |
Optional range of adapters and socket converters also available |
|
