 |
| datasheet |
|
448Pro |
 |
The 448Pro is a PC based gang programmer featuring four
independent universal programming modules and USB 2.0 connectivity.
Supporting over 20,000 devices with new support added monthly, the
448Pro can program without the need for a family-specific
modules, giving you the freedom to choose the optimal device for your
design.
|
|
The 448Pro is built to meet the demands of high volume production
programming with minimal operator effort. Concurrent and semiconcurrent
programming options combine with device insertion tests
and a user friendly interface to give higher programming yields and
reduced failure rates. |
- FPGA based totally reconfigurable 48 owerful TTL pindrivers
provide H/L/pull_up/pull_down and read
capability for each pin of socket. Advanced pindrivers incorporate high-quality
high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported devices.
Pin drivers operate down to
1.8V so you'll be ready to program the full range of today's advanced low-voltage
devices.
- Each programming module performs device insertion tests and contact
checks before it programs each
device. These capabilities, supported by overcurrent protection
and signature-byte check help prevent chip
damage due to operator error.
- Self test capability allows diagnostic software to thoroughly
check the health of the each programming
module.
- Built-in protection circuits eliminate damage of the programming
module and/or programmed device due
to environment or operator failure. All ZIF socket pin inputs
of the 448Pro programmer are
protected against ESD up to 15kV.
- 448Pro programmer performs programming verification
at the marginal level of supply voltage,
improving yield and guarantees long data retention.
- Various socket converters are available to handle device in
PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN
(MLF), SDIP, BGA and other packages.
|
User Interface Production Mode Control
- This part of the software is focused on easy monitoring of high-volume
production operations.
- Operator-friendly control software combines many powerful functions
with
ease of use. Graphic user interface provides an overview of all the important
activities without burdening the operator with less-important details.
- A project file is used to control the 448Pro multiprogramming system.
Project files contain user data, chip programming setup information,
chip
configuration data, auto programming command sequence, etc. This
minimizes potential operator errors because the project file can be created
and verified by a qualified engineer before being passed to the operator.
The
optional protected mode can be set for project file to avoid unwanted
changes to the project file.
- Each chip may be programmed with different data such as serial number,
configuration and calibration information.
Engineering Mode Control
- This part of the software is used for quick and easy preparation of project
files for use in the production mode control software.
- Each programming module is driven by an easy-to-use control program
with
pull-down menu, hot keys and on-line help. Selection of device is performed
by its class and manufacturer or simply by typing a fragment of vendor
name and/or part number. It is the same proven software, used by both
the
40Pro and 48Pro programmers.
- Standard device-related commands (read, blank check, program, verify,
erase)
are enhanced by test functions (insertion test, connection check, signaturebyte
check), and additional special functions (auto increment, production
mode – programming starts immediately after insertion of chip into
the
socket).
- All known data formats are supported with automatic file format detection
and conversion during loading. Support for Jam (JEDEC standard JESD-71)
and VME files is also included.
- The comprehensive auto-increment function allows each programmed device
to be assigned an individual or incrementing serial number. This function
also
enables the operator to read serial numbers or device identification
signatures from a file.
- The software also provides comprehensive information about the supported
device, including drawings of all available packages and explanations
of
prefixes/suffixes.
- Keeping your programmer software up to date can be a costly business
with
some programmers. Dataman offers completely FREE software updates
whenever you need them. The latest software is always available from
our
website.
|
The 448Pro supports over 20,000 of the most popular
devices in use
today - with future devices being added monthly.
|
Programmer,
in ZIF socket
- BI-PROM
- EPROM
- EEPROM
- EPLD
- CPAL
|
|
- NVRAM
- PAL
- PEEL
- PLD
- MICROCONTROLLERS
|
|
| Programmer |
| |
USB 2.0 port |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Autocalibration/self test capability |
| ZIF socket, pindriver |
| |
4 x 48 pin DIL ZIF (Zero Insertion Force) sockets accepting 300/600
mil
devices up to 48 pin |
| |
Pindrivers: 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| Package Includes |
| |
448Pro Universal Gang Production Programmer
Dimensions: 506x213x86 mm (19.9x8.4x3.4 inches)
Weight: 4.8kg (10.58 lb) |
| |
Switching power adapter
100/240V, max 1.2A, 50-60Hz |
| |
Moulded USB Cable |
| |
Diagnostic POD for self test of the programmer |
| |
Anti-dust cover for ZIF socket |
| |
User manual |
| |
Software (2000/XP/2003/XPx64) |
| |
Transport case |
| |
Optional range of
adapters and
socket converters
also available |
|
