|
|
448Pro2
Super Fast Gang ISP Production Programmer |
 |
The 448Pro2 is a super fast PC based gang programmer
with
four independent 48-pin ZIF sockets, ISP capabilities and USB 2.0
connectivity. The 448Pro2 is built to meet the demands of super fast
high volume production programming with minimal operator effort.
Supporting over 51,000 (Jan 2010) devices with new support being
added monthly, the Dataman 448Pro2 can program without the need
for family-specific modules, giving you the freedom to choose the
optimal device for your design. Independent programming options
combine with device insertion tests and a user friendly interface
to give
higher programming yields and reduced failure rates. |
- The 448Pro2 programmer offers the same advanced features
as the 448Pro+ programmer but with up to
70% faster programming of high-capacity memory devices.
- FPGA based totally reconfigurable 48 powerful TTL pindrivers provide
H/L/pull_up/pull_down and read
capability for each pin of the socket. Advanced pindrivers incorporate
high-quality high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported
devices. Pin drivers operate down to
1.8V so you'll be ready to program the full range of tomorrow's
advanced low-voltage devices.
- Each programming module performs device insertion tests and contact
checks before it programs each
device. These capabilities, supported by overcurrent protection
and signature-byte check, help prevent chip
damage due to operator error.
- Selftest capability allows diagnostics in the software to
thoroughly check the health of the programmer.
- Built-in protection circuits eliminate damage of the programming
module and/or programmed device due
to environment or operator failure. All ZIF socket pin inputs
of the Dataman 448Pro2 programmer are
protected against ESD up to 15kV.
- The 448Pro2 programmer performs programming verification at the marginal
levels of supply voltage,
improving programming yield and guaranteeing long data retention.
- Wide range of socket converters are available to handle devices
in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP,
TQFP, QFN (MLF), SDIP, BGA and other packages.
|
Production Mode Control
- This part of the software is focused to the easy monitoring of
high-volume production operations.
- Operator-friendly control software combines many powerful functions
with ease of use. Graphic user interface provides an overview of
important information, reducing the burden on the operator with unnecessary
details.
- Project files are used to control the 448Pro2 and contain
user data, chip
programming setup, chip configuration, auto programming command
sequence. This helps minimize operator error as the project file
is normally
created by an engineer and then passed to the operator. The optional
protected mode can be set avoiding unwanted changes to the project
file.
- Each chip may be programmed with different data such as serial
number, configuration and calibration information.
Engineering Mode Control
- This part of the software is focused to the quick and easy preparation
of the project file for usage in the production mode control software.
- Each programming module is driven by an easy-to-use control program
with pull-down menus, hot keys and on-line help. Selecting a device
is performed by its class, by manufacturer or simply by typing
a fragment of vendor name and/or part number.
- Standard device-related commands (read, blank check, program,
verify, erase) are enhanced by test functions (insertion test,
signature-byte check) and additional special functions (autoincrement,
production mode - programming starts immediately once chip inserted
into socket).
- All known data formats are supported. Automatic file format
detection and conversion during loading of file.
- The software provides extensive information about programmable
devices including detailed drawings of all available packages.
The software also provides explanations of chip labelling (prefixes
and suffixes) for each of the supported chips.
|
The 448Pro2 supports over 51,000 of the most popular
devices in use today - with future devices being added monthly. Dataman
448Pro2 coverage includes the following device types:
Programmer (ZIF Socket)
EPROM, EEPROM, Flash EPROM, NAND Flash, LBA-NAND, mDOC H3, multi-chip
devices, FRAM, MRAM, NV RAM, PROM, Serial E(E)PROM, Serial Flash,
Configuration (EE)PROM, 1-Wire E(E)PROM, PLD, FPGA, Clocks, Microcontrollers
Programmer (ISP Connector)
Serial E(E)PROM, 1-Wire E(E)PROM, Serial Flash, Microcontrollers, PLD, FPGA
|
| Base Unit (DAC) |
| |
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Selftest capability |
| ZIF socket |
| |
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin |
| |
Pindrivers: 4 x 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
20-pin male type with missinsertion lock |
| |
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable from 1.8V up to 5V to handle all (including low-voltage)
devices |
| |
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins |
| |
Programmed chip voltage (VCCP) with both source/sink capability
and voltage sense |
| |
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins |
| |
Target system supply voltage (range 2V..6V/250mA) |
| |
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV
air, 8kV contact) |
| |
Two output signals, which indicate state of work result = LED OK
and LED Error (active level: min 1.8V) |
| |
Input signal, switch YES! equivalent (active level: max. 0.8V) |
| Package Includes |
| |
Dataman 448Pro2+ Universal Gang Production Programmer
- Dimensions: 361 x 234 x 56mm (14.2 x 9.2 x 2.2inches)
- Weight: 3.5Kg (7.72lbs)
- Operating voltage: 100-240V
- Power consumption: max. 60W active |
| |
Moulded USB Cable |
| |
Diagnostic POD for ZIF socket selftest of the programmer (x1) |
| |
Diagnostic POD for ISP connector selftest of the programmer (x1) |
| |
ISP cable (x4) |
| |
Anti-dust cover for ZIF socket (x4) |
| |
ESD wrist strap with cord and banana plug |
| |
User manual |
| |
Software
- Compatible with Windows 98, Windows ME, Windows NT, Windows 2000,
Windows 2003, Windows XP, Windows Vista and Windows 7 |
| |
Transport case |
| |
Optional range of adapters and socket converters also available |
|
