|
|
448Pro+
Gang ISP Production Programmer |
 |
Universal ISP gang programmer with four independent 48-pin
ZIF sockets and USB 2.0 connectivity. Independent programming options
combine with device insertion tests and a user friendly interface to
give higher programming yields and reduced failure rates.
The 448Pro+ is built to meet the demands of high volume production
programming with minimal operator effort. |
- FPGA based totally reconfigurable 48 powerful TTL pindrivers
provide H/L/pull_up/pull_down and read capability for each pin of
socket. Advanced pindrivers incorporate high-quality high-speed circuitry
to deliver signals without overshoot or ground bounce for all supported
devices. Pin drivers operate down to 1.8V so you'll be ready to program
the full range of tomorrows advanced low-voltage devices.
- Each programming module performs device insertion and contact tests
before programming each device. These capabilities, supported by overcurrent
protection and signature-byte check help prevent chip damage due to
operator error.
- The selftest capability allows diagnostics included in the software
to thoroughly check the health of the each programming module.
- Built-in protection circuits eliminate damage to programming
modules and/or programmed devices due to environment or operator
failure. All ZIF sockets and ISP connector pins are protected
against ESD up to 15kV.
- 448Pro+ programmer performs programming verification at the
marginal level of supply voltage, improving programming yield
and guarantees long data retention.
- Various socket converters are available to handle device in PLCC, SOIC,
PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages.
|
Production Mode Control
- This part of the software is focused to the easy monitoring of
high-volume production operations.
- Operator-friendly control software combines many powerful functions
with ease of use. Graphic user interface provides an overview of
important information, reducing the burden on the operator with unnecessary
details.
- Project files are used to control the 448Pro+ multiprogrammer.
The project files contain user data, chip programming setup,
chip configuration, auto programming command sequence, etc.
This helps minimize operator error as the project file is normally
created and proofed by engineer and passed to the operator.
The optional protected mode can be set avoiding unwanted changes
to the project file.
- Each chip may be programmed with different data such as serial
number, configuration and calibration information.
Engineering Mode Control
- This part of the software is focused to the quick and easy preparation
of the project file for usage in the production mode control software.
- Each programming module is driven by an easy-to-use control program
with pull-down menus, hot keys and on-line help. Selecting of device
is performed by its class, by manufacturer or simply by typing a
fragment of vendor name and/or part number.
- Standard device-related commands (read, blank check, program,
verify, erase) are enhanced by test functions (insertion test,
signature-byte check) and additional special functions (autoincrement,
production mode - programming starts immediately once chip inserted
into socket).
- All known data formats are supported. Automatic file format
detection and conversion during loading of file. Jam file (JEDEC
standard JESD-71) and VME file compatible.
- The versatile auto-increment function allows each programmed
device to be assigned an individual or incrementing serial number.
This function also enables the operator to read serial numbers
or device identification signatures from a file.
- The software provides extensive information about programmable
devices including detailed drawings of all available packages.
The software also provides explanations of chip labelling (prefixes
and suffixes) for each of the supported chips.
- Keeping your programmer software up to date can be a costly
business with some programmers. Dataman offers completely FREE
software updates whenever you need them.
|
The 448Pro+ supports over 51,000 of the most popular
devices in use today - with future devices being added monthly. Dataman
448Pro+ coverage includes the following device types:
Programmer (ZIF Socket)
1-Wire E(E)PROM, BI-PROM, Configuration (EE)PROM, CPAL, EEPROM, EPROM,
EPLD, Flash, Flash EPROM, FPGA, GAL, MACH, Microcontrollers, MROM, NV RAM,
PAL, PEEL, PLD, PROM, Serial E(E)PROM
Programmer (ISP Connector)
Microcontrollers, PLD, Serial E(E)PROM
|
| Base Unit (DAC) |
| |
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Selftest capability |
| ZIF socket |
| |
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin |
| |
Pindrivers: 4 x 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
20-pin male type with missinsertion lock |
| |
5 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable from 1.8V up to 5V to handle all (including low-voltage)
devices |
| |
1x VCCP voltage (range 2V..7V/100mA), can be applied to pins 1,
3 |
| |
Programmed chip voltage (VCCP) with both source/sink capability
and voltage sense |
| |
1x VPP voltage (range 2V..25V/50mA), can be applied to pins 2,3,4,6,8,10 |
| |
Target system supply voltage (range 2V..6V/250mA) |
| |
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV
air, 8kV contact) |
| Package Includes |
| |
Dataman 448Pro+ Universal Gang Production Programmer
- Dimensions: 361 x 234 x 56mm (14.2 x 9.2 x 2.2inches)
- Weight: 3.5Kg (7.72lbs)
- Operating voltage: 100-240V
- Power consumption: max. 60W active |
| |
Moulded USB Cable |
| |
Diagnostic POD for ZIF socket selftest of the programmer (x1) |
| |
Diagnostic POD for ISP connector selftest of the programmer (x1) |
| |
ISP cable (x4) |
| |
Anti-dust cover for ZIF socket (x4) |
| |
ESD wrist strap with cord and banana plug |
| |
User manual |
| |
Software
- Compatible with Windows 98, Windows ME, Windows NT, Windows 2000,
Windows 2003, Windows XP, Windows Vista and Windows 7 |
| |
Transport case |
| |
Optional range of adapters and socket converters also available |
|
