|
|
48Pro2
Super Fast Universal ISP Programmer |
 |
The Dataman 48Pro2 is a super fast PC based universal 48-pin
programmer with ISP capabilities and USB 2.0 / parallel connectivity.
The 48Pro2 is built to meet the demands of development labs and field
engineers for super fast universal programming.
Supporting over 51,000 (Jan 2010) devices with new support being added
monthly, the Dataman 48Pro2 can program without the need for familyspecific
modules, giving you the freedom to choose the optimal device for
your design. Using the built-in, in-system programming (ISP) connector,
the programmer is able to program ISP compatible chips in circuit. |
- The 48Pro2 programmer offers the same advanced features
as the 48Pro+ programmer but with up to
70% faster programming of high-capacity memory devices.
- FPGA based totally reconfigurable 48 powerful TTL pindrivers provide
H/L/pull_up/pull_down and read
capability for each pin of the socket. Advanced pindrivers incorporate
high-quality high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported
devices. Improved pin drivers operate
down to 1.8V so you'll be ready to program the full range of
tomorrows advanced low-voltage devices.
- The programmer performs device insertion and contact tests before
programming each device. These
capabilities, supported by overcurrent protection and signature-byte
check, help prevent chip damage due
to operator error.
- Selftest capability allows diagnostics in the software to
thoroughly check the health of the programmer.
- Built-in protection circuits eliminate damage to the programmer
and/or programmed devices due to
environment or operator failure. All the inputs of the 48Pro2
programmer, including ZIF socket, connection
to PC and power supply input are protected against ESD up to
15kV.
- The 48Pro2 programmer performs programming verification at
the marginal levels of supply voltage,
improving programming yield and guaranteeing long data retention.
- Wide range of socket converters are available to handle devices
in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP,
TQFP, QFN (MLF), SDIP, BGA and other packages.
|
- The programmer is driven by an easy-to-use control program with
pull-down
menus, hot keys and on-line help. Selecting a device is performed by
its class,
by manufacturer or simply by typing a fragment of the vendor name and/or
part number.
- Standard device-related commands (read, blank check, program, verify,
erase)
are enhanced by test functions (insertion test, signature-byte
check) and
additional special functions (auto-increment serialisation, production
mode -
programming starts immediately after chip is inserted).
- All known data formats are supported. Automatic file format
detection and
conversion performed during loading of file.
- The versatile auto-increment function allows each programmed
device to be
assigned an individual or incrementing serial number. This function
also
enables the operator to use serial numbers or device identification
signatures
from an external file.
- The software provides extensive information about programmable
devices
including detailed drawings of all available packages. The software
also
provides explanations of chip labelling (prefixes and suffixes).
- The software provides full information for ISP implementation:
Description of
ISP connector pins, recommended target design and other necessary
details.
- The remote control feature allows the software to be flow
controlled by
another application - either using .BAT file commands or DLL
file
(C/PAS/VBASIC/.NET).
- Multiple devices can be programmed and tested via a JTAG chain:
JTAG chain
(ISP-Jam), JTAG chain (ISP-VME), JTAG chain (ISP-SVF) or JTAG
chain (ISP-STP).
- Multiple 48Pro2 programmers can be operated from the same
PC creating a
high volume production environment with all the benefits of
the standard
48Pro2. Up to four 48Pro2 programmers can be connected simultaneously
providing a highly scalable gang programming system.
|
The 48Pro2 supports over 51,000 (Jan 2010) of the most popular
devices in use today - with new devices being added monthly. 48Pro2
coverage includes the following device types:
Programmer (ZIF Socket)
EPROM, EEPROM, Flash EPROM, NAND Flash, LBA-NAND, mDOC H3, multi-chip
devices, FRAM, MRAM, NV RAM, PROM, Serial E(E)PROM, Serial Flash,
Configuration (EE)PROM, 1-Wire E(E)PROM, PLD, FPGA, Clocks, Microcontrollers
Programmer (ISP Connector)
Serial E(E)PROM, 1-Wire E(E)PROM, Serial Flash, Microcontrollers, PLD, FPGA
|
| Base Unit (DAC) |
| |
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate |
| |
FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Selftest capability |
| |
Protection against surge and ESD on power supply input and parallel
port connection |
| |
Banana jack for ESD wrist strap connection |
| |
Banana jack for connection to ground |
| ZIF socket |
| |
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin |
| |
Pindrivers: 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
20-pin male type with missinsertion lock |
| |
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable from 1.8V up to 5V to handle all (low-voltage including)
devices |
| |
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins |
| |
Programmed chip voltage (VCCP) with both source/sink capability
and voltage sense |
| |
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins |
| |
Target system supply voltage (range 2V..6V/250mA) |
| |
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV
air, 8kV contact) |
| |
Two output signals, which indicate state of work result = LED OK
and LED Error (active level: min 1.8V) |
| |
Input signal, switch YES! equivalent (active level: max. 0.8V) |
| Package Includes |
| |
48Pro2 Universal ISP Production Programmer
- Dimensions: 195 x 140 x 55mm (7.7 x 5.5 x 2.2inches)
- Weight: 0.9Kg (1.98lbs)
- Operating voltage: 110-250V AC
- Power consumption: max. 20W active / approx. 2W sleep |
| |
Power Cable |
| |
Moulded USB Cable |
| |
ISP cable |
| |
Diagnostic POD for self test of the programmer |
| |
Diagnostic POD for selftest of the ISP connector |
| |
Anti-dust cover for ZIF socket |
| |
User manual |
| |
Software
- Compatible with Windows 98, Windows ME, Windows NT, Windows 2000,
Windows 2003, Windows XP, Windows Vista and Windows 7 |
| |
Optional range of adapters and socket converters also available |
|
