|
|
48Pro+
Universal ISP Programmer |  |
The 48Pro+ is a PC based universal 48-pin programmer
with
ISP capabilities / USB 2.0 and parallel connectivity. The 48Pro+ is built
to meet the demands of development labs and field engineers for
universal programming.
Supporting over 51,000 devices with new support being added monthly,
the 48Pro+ can program without the need for a family-specific
module, giving you the freedom to choose the optimal device
for your design. Using the built-in, in-circuit serial programming (ISP)
connector, the programmer is able to program ISP compatible chips in
circuit. |
- FPGA based totally reconfigurable 48 powerful TTL pindrivers provide
H/L/pull_up/pull_down and read
capability for each pin of socket. Advanced pindrivers incorporate high-quality
high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported devices.
Pin drivers operate down to
1.8V so you'll be ready to program the full range of tomorrows advanced
low-voltage devices.
- The programmer performs device insertion and contact tests before
programming each device. These
capabilities, supported by overcurrent protection and signature-byte
check help prevent chip damage due
to operator error.
- Built-in protection circuits eliminate damage to the programmer
and/or programmed device due to
environment or operator failure. All the inputs of the 48Pro+
programmer, including ZIF socket, connection
to PC and power supply input are protected against ESD up to 15kV.
- 48Pro+
programmer performs programming verification at the marginal
level of supply voltage, improving
programming yield and guarantees long data retention.
- Various socket converters are available to handle device in
PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN
(MLF), SDIP, BGA and other packages.
|
- Programmer is driven by an easy-to-use control program with pull-down
menu, hot keys and on-line help. Selecting of device is performed by
its class,
by manufacturer or simply by typing a fragment of vendor name and/or
part
number.
- Standard device-related commands (read, blank check, program, verify,
erase)
are enhanced by test functions (insertion test, signature-byte
check) and
additional special functions (autoincrement, production mode -
programming starts immediately once chip inserted into socket).
- All
known data formats are supported. Automatic file format detection
and
conversion during loading of file.
- The rich-featured auto-increment function enables one to assign
individual
serial numbers to each programmed device - or simply increments
a serial
number, or the function enables one to read serial numbers or
any
programmed device identification signatures from a file.
- The software provides extensive information about programmable
devices
including detailed drawings of all available packages. The software
also
provides explanations of chip labelling (prefixes and suffixes)
for each of the
supported chips.
- The software provides full information for ISP implementation:
Description
of ISP connector pins, recommended target design and other necessary
information.
- The remote control feature allows the PG4UW software to be
flow controlled
by another application - either using .BAT file commands or
DLL file
(C/PAS/VBASIC/.NET).
- Multiple devices can be programmed and tested via JTAG chain:
JTAG chain
(ISP-Jam) or JTAG chain (ISP-VME).
- Multiple 48Pro+ programmers can be connected to the same PC
(via USB
port) achieving an extremely powerful multiprogramming system,
supporting
as many devices as a single 48Pro+ programmer and without a
noticeable
decrease in programming speed. Concurrent multiprogramming is
also
supported allowing each programmer to work independently increasing
throughput.
|
The 48Pro+ supports over 51,000 of the most popular
devices in use today - with future devices being added monthly.
48Pro+ coverage includes the following device types:
Programmer (ZIF Socket)
1-Wire E(E)PROM, BI-PROM, Configuration (EE)PROM, CPAL, EEPROM, EPROM, EPLD,
Flash, Flash EPROM, FPGA, GAL, MACH, Microcontrollers, MROM, NV RAM, PAL, PEEL,
PLD, PROM, Serial E(E)PROM
Programmer (ISP Connector)
Microcontrollers, PLD, Serial E(E)PROM
|
| Base Unit (DAC) |
| |
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate |
| |
FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Selftest capability |
| |
Protection against surge and ESD on power supply input and parallel
port connection |
| |
Banana jack for ESD wrist strap connection |
| |
Banana jack for connection to ground |
| ZIF socket |
| |
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin |
| |
Pindrivers: 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
20-pin male type with missinsertion lock |
| |
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable from 1.8V up to 5V to handle all (low-voltage including)
devices |
| |
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins |
| |
Programmed chip voltage (VCCP) with both source/sink capability
and voltage sense |
| |
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins |
| |
Target system supply voltage (range 2V..6V/250mA) |
| |
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV
air, 8kV contact) |
| |
Two output signals, which indicate state of work result = LED OK
and LED Error (active level: min 1.8V) |
| |
Input signal, switch YES! equivalent (active level: max. 0.8V) |
| Package Includes |
| |
48Pro+ Universal ISP Production Programmer
- Dimensions: 195 x 140 x 55mm (7.7 x 5.5 x 2.2inches)
- Weight: 0.9Kg (1.98lbs)
- Operating voltage: 110-250V AC
- Power consumption: max. 20W active / approx. 2W sleep |
| |
Power Cable |
| |
Moulded USB Cable |
| |
ISP cable |
| |
Diagnostic POD for self test of the programmer |
| |
Diagnostic POD for selftest of the ISP connector |
| |
Anti-dust cover for ZIF socket |
| |
User manual |
| |
Software
- Compatible with Windows 98, Windows ME, Windows NT, Windows 2000,
Windows 2003, Windows XP, Windows Vista and Windows 7 |
| |
Optional range of adapters and socket converters also available |
|
