|
|
848Pro2
Super Fast Stand-Alone Production Programmer |
 |
Super fast universal stand-alone gang programmer with eight
independent 48-pin ZIF sockets and internal control PC driven by Windows
XP Embedded. Concurrent programming options combine with device insertion
tests and a user friendly interface to give higher programming yields
and reduced failure rates.
The 848Pro2 is built to meet the demands of high volume production programming
with minimal operator effort. |
- The 848Pro2 programmer offers the same advanced features
as the 848Pro+ programmer but with up to
70% faster programming of high-capacity memory devices.
- FPGA based totally reconfigurable 48 powerful TTL pindrivers provide
H/L/pull_up/pull_down and read
capability for each pin of the socket. Advanced pindrivers incorporate
high-quality high-speed circuitry to
deliver signals without overshoot or ground bounce for all supported
devices. Pin drivers operate down to
1.8V so you'll be ready to program the full range of tomorrow's
advanced low-voltage devices.
- Each programming module performs device insertion tests and contact
checks before it programs each
device. These capabilities, supported by overcurrent protection
and signature-byte check, help prevent chip
damage due to operator error.
- Selftest capability allows diagnostics in the software to
thoroughly check the health of the programmer.
- Built-in protection circuits eliminate damage to programming
modules and/or programmed devices due to
environment or operator failure. All ZIF sockets and ISP connector
pins are protected against ESD up to
15kV.
- The 848Pro2 programmer performs programming verification at the marginal
levels of supply voltage,
improving programming yield and guaranteeing long data retention.
- Wide range of socket converters are available to handle devices
in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP,
TQFP, QFN (MLF), SDIP, BGA and other packages.
|
There are two ways to control and monitor the 848Pro2
programmer:
- The graphical control unit with touch screen provides essential
information
about the programming flow and allows basic control of the 848Pro2
- Using a display, keyboard and mouse allows access to all programming
flow
information and options.
Production Mode Control
- This part of the software is focused to the easy monitoring of
high-volume production operations.
- Operator-friendly control software combines many powerful functions
with ease of use. Graphic user interface provides an overview of
important information, reducing the burden on the operator with unnecessary
details.
- Project files are used to control the 848Pro2 stand-alone
multiprogrammer. The project files contain user data, chip
programming setup,
chip configuration, auto programming command sequence, etc.
This helps minimize operator error as the project file is
normally created and proofed by engineer and passed to the
operator.
The optional protected mode can be set avoiding unwanted changes
to the project file.
- Each chip may be programmed with different data such as serial
number, configuration and calibration information.
Engineering Mode Control
- This part of the software is focused to the quick and easy preparation
of the project file for usage in the production mode control software.
- Each programming module is driven by an easy-to-use control program
with pull-down menus, hot keys and on-line help. Selecting of device
is performed by its class, by manufacturer or simply by typing a
fragment of vendor name and/or part number.
- Standard device-related commands (read, blank check, program,
verify, erase) are enhanced by test functions (insertion test,
connection check, signature-byte check) and additional special
functions (autoincrement, production mode - programming starts
immediately once chip inserted into socket).
- All known data formats are supported. Automatic file format
detection and conversion during loading of file.
- The software provides extensive information about programmable
devices including detailed drawings of all available packages.
The software also provides explanations of chip labelling
(prefixes and suffixes).
|
The 848Pro2 supports over 51,000 of the most popular
devices in use
today - with future devices being added monthly. 848Pro2 coverage
includes the following device types:
Programmer (ZIF Socket)
EPROM, EEPROM, Flash EPROM, NAND Flash, LBA-NAND, mDOC H3, multi-chip
devices, FRAM, MRAM, NV RAM, PROM, Serial E(E)PROM, Serial Flash,
Configuration (EE)PROM, 1-Wire E(E)PROM, PLD, FPGA, Clocks, Microcontrollers
Programmer (ISP Connector)
Serial E(E)PROM, 1-Wire E(E)PROM, Serial Flash, Microcontrollers, PLD,
FPGA
|
| Base Unit (DAC) |
| |
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate |
| |
On-board intelligence: powerful microprocessor and FPGA based state
machine |
| |
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise
and fall time |
| |
VCCP range 0..8V/1A |
| |
VPP1, VPP2 range 0..26V/1A |
| |
Selftest capability |
| ZIF socket |
| |
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600
mil devices up to 48-pin |
| |
Pindrivers: 8 x 48 universal |
| |
VCCP/VPP1/VPP2 can be connected to each pin |
| |
Perfect ground for each pin |
| |
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on
all pindriver
pins |
| |
Analog pindriver output level selectable from 1.8 V up to 26V |
| |
Current limitation, overcurrent shutdown, power failure shutdown |
| |
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV
contact) |
| |
Continuity test: each pin is tested before every programming operation |
| ISP connector |
| |
20-pin male type with missinsertion lock |
| |
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level
H selectable from 1.8V up to 5V to handle all (including low-voltage)
devices |
| |
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins |
| |
Programmed chip voltage (VCCP) with both source/sink capability
and voltage sense |
| |
1x VPP voltage (range 2V..25V/50mA), can be applied to 6 pins |
| |
Target system supply voltage (range 2V..6V/250mA) |
| |
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV
air, 8kV contact) |
| |
Two output signals, which indicate state of work result = LED OK
and LED Error (active level: min 1.8V) |
| |
Input signal, switch YES! equivalent (active level: max 0.8V) |
| Package Includes |
| |
848Pro Stand-Alone Production Programmer
- Processor: Intel Core 2 Quad 2.66 GHz
- Memory: 2 GB
- Hard drive: 320 GB
- Operating system: Microsoft Windows XP
- Dimensions: 625 x 465 x 115mm (24.6 x 18.3 x 4.5inches)
- Weight: 14.9Kg (32.85lbs)
- Operating voltage: 100-240V
- Power consumption: max. 300W active |
| |
Diagnostic POD for ZIF socket selftest of the programmer (x1) |
| |
Diagnostic POD for ISP connector selftest of the programmer (x1) |
| |
ISP cable (x8) |
| |
Anti-dust cover for ZIF socket (x8) |
| |
ESD wrist strap with cord and banana plug |
| |
User manual |
| |
Software |
| |
Transport case |
| |
Optional range of adapters and socket converters also available |
|
